 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| No. STSE-CH2058C SPECIFICATIONS FOR NICHIA UV LED MODEL : NSHU590A NICHIA CORPORATION -0- Nichia STSE-CH2058C Symbol IF IFP IR PD Topr Tstg Tsld Absolute Maximum Rating 25 80 85 100 -30 ~ + 85 -40 ~ +100 265C for 10sec. (Ta=25C) Unit mA mA mA mW C C IFP Conditions : Pulse Width < 10msec. and Duty < 1/10 = = (2) Initial Electrical/Optical Characteristics Item Symbol Forward Voltage VF Peak Wavelength P Spectrum Half Width ! Rank 2 Po Optical Power Output Rank 3 Po Rank 4 Po ! !! Condition IF=20[mA] IF=20[mA] IF=20[mA] IF=20[mA] IF=20[mA] IF=20[mA] Min. 370 850 1200 1700 Typ. 3.5 375 10 1000 1400 2000 (Ta=25C) Max. Unit 4.0 V 380 nm nm W 1200 W 1700 W 2400 Optical Power Output Measurement allowance is 10%. Peak Wavelength Measurement allowance is 3nm. The quantity-ratio of the three ranks is decided by Nichia. !!! One delivery will include up to three different ranks of the products. 2.TYPICAL INITIAL OPTICAL/ELECTRICAL CHARACTERISTICS Please refer to figure's page. 3.OUTLINE DIMENSIONS AND MATERIALS Please refer to figure's page. Material as follows ; Glass : Material as follows ; Cap : Material as follows ; Lead : Hard Glass Ni Plating Iron Alloy Au Plating Iron Alloy -1- Nichia STSE-CH2058C 4.PACKAGING * The LEDs are packed in cardboard boxes after packaging in anti-electrostatic bags. Please refer to figure's page. The label on the minimum packing unit shows ; Part Number, Lot Number, Ranking, Quantity * In order to protect the LEDs from mechanical shock, we pack them in cardboard boxes for transportation. * The LEDs may be damaged if the boxes are dropped or receive a strong impact against them, so precautions must be taken to prevent any damage. * The boxes are not water resistant and therefore must be kept away from water and moisture. * When the LEDs are transported, we recommend that you use the same packing method as Nichia. 5.LOT NUMBER The first six digits number shows lot number. The lot number is composed of the following characters; "#$$$$ - !% " - Year ( 3 for 2003, 4 for 2004 ) # - Month ( 1 for Jan., 9 for Sep., A for Oct., $$$$ - Nichia's Product Number ! - Ranking by Wavelength % - Ranking by Optical Power Output B for Nov. ) -2- Nichia STSE-CH2058C 6.RELIABILITY (1) TEST ITEMS AND RESULTS Test Item Resistance to Soldering Heat Solderability Thermal Shock Temperature Cycle Moisture Resistance Cyclic Terminal Strength (bending test) Terminal Strength (pull test) High Temperature Storage Temperature Humidity Storage Low Temperature Storage Steady State Operating Life Steady State Operating Life of High Humidity Heat Steady State Operating Life of Low Temperature Standard Test Method JEITA ED-4701 300 302 JEITA ED-4701 300 303 JEITA ED-4701 300 307 JEITA ED-4701 100 105 JEITA ED-4701 200 203 JEITA ED-4701 400 401 JEITA ED-4701 400 401 JEITA ED-4701 200 201 JEITA ED-4701 100 103 JEITA ED-4701 200 202 Test Conditions Tsld=260 5C, 10sec. 3mm from the base of the epoxy bulb Tsld=235 5C, (using flux) 0C ~ 100C 15sec. 15sec. -40C ~ 25C ~ 100C ~ 25C 30min. 5min. 30min. 5min. 25C ~ 65C ~ -10C 90%RH 24hrs./1cycle Load 5N (0.5kgf) 0 ~ 90 ~ 0 bend 2 times Load 10N (1kgf) 10 1 sec. Ta=100C Ta=60C, RH=90% Ta=-40C Ta=25C, IF=25mA 60C, RH=90%, IF=15mA Ta=-30C, IF=20mA 5sec. Note 1 time 1 time over 95% 100 cycles 100 cycles 10 cycles No noticeable damage No noticeable damage 1000hrs. 1000hrs. 1000hrs. 500hrs. 500hrs. Number of Damaged 0/100 0/100 0/100 0/100 0/100 0/100 0/100 0/100 0/100 0/100 0/100 0/100 1000hrs. 0/100 (2) CRITERIA FOR JUDGING THE DAMAGE Item Symbol Test Conditions Forward Voltage VF IF=20mA U.S.L.*)$ 1.1 Optical Power Output Po IF=20mA L.S.L.**)$ 0.7 *) U.S.L. : Upper Standard Level **) L.S.L. : Lower Standard Level Criteria for Judgement Min. Max. -3- Nichia STSE-CH2058C 7.CAUTIONS (1) Cautions * The devices are UV light LEDs. The LED during operation radiates intense UV light, which precautions must be taken to prevent looking directly at the UV light with unaided eyes. Do not look directly into the UV light or look through the optical system. When there is a possibility to receive the reflection of light, protect by using the UV light protective glasses so that light should not catch one's eye directly. * Put the caution label on the cardboard box. UV LED LED 1M LED LED RADIATION DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS CLASS 1M LED PRODUCT (2) Lead Forming * When forming leads, the leads should be bent at a point at least 3mm from the base of the lead. Do not use the base of the leadframe as a fulcrum during lead forming. * Lead forming should be done before soldering. * Do not apply any bending stress to the base of the lead. The stress to the base may damage the LED's characteristics or it may break the LEDs. * When mounting the LEDs onto a printed circuit board, the holes on the circuit board should be exactly aligned with the leads of the LEDs. If the LEDs are mounted with stress at the leads, it causes deterioration of the lead and this will degrade the LEDs. (3) Storage * The LEDs should be stored at 30C or less and 70%RH or less after being shipped from Nichia and the storage life limits are 3 months. If the LEDs are stored for 3 months or more, they can be stored for a year in a sealed container with a nitrogen atmosphere and moisture absorbent material. * Nichia LED leads are comprised of a gold plated Iron alloy. The gold surface may be affected by environments which contain corrosive gases and so on. Please avoid conditions which may cause the LED to corrode, tarnish or discolor. This corrosion or discoloration may cause difficulty during soldering operations. It is recommended that the LEDs be used as soon as possible. * Please avoid rapid transitions in ambient temperature, especially, in high humidity environments where condensation can occur. (4) Static Electricity * Static electricity or surge voltage damages the LEDs. It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs. * All devices, equipment and machinery must be properly grounded. It is recommended that measures be taken against surge voltage to the equipment that mounts LEDs. * When inspecting the final products in which LEDs were assembled, it is recommended to check whether the assembled LEDs are damaged by static electricity or not. It is easy to find static-damaged LEDs by a light-on test or a VF test at a lower current (below 1mA is recommended). The LEDs should be used the light detector etc. when testing the light-on. Do not stare into the LEDs when testing. * Damaged LEDs will show some unusual characteristics such as the forward voltage becomes lower, or the LEDs do not light at the low current. Criteria : (VF > 2.0V at IF=0.5mA) -4- Nichia STSE-CH2058C Pre-Heat Pre-Heat Time Solder Bath Temperature Dipping Time Dipping Position Dip Soldering 120C Max. 60 seconds Max. 260C Max. 10 seconds Max. No lower than 3 mm from the base of the lead. Temperature Soldering Time Position Soldering 350C Max. 3 seconds Max. No closer than 3 mm from the base of the lead. * Do not apply any stress to the lead particularly when heated. * The LEDs must not be repositioned after soldering. * After soldering the LEDs, the lead should be protected from mechanical shock or vibration until the LEDs return to room temperature. * Direct soldering onto a PC board should be avoided. Mechanical stress to the glass may be caused from warping of the PC board or from the clinching and cutting of the leads. When it is absolutely necessary, the LEDs may be mounted in this fashion but the User will assume responsibility for any problems. Direct soldering should only be done after testing has confirmed that no damage, such as wire bond failure or glass deterioration, will occur. Nichia's LEDs should not be soldered directly to double sided PC boards because the heat will deteriorate the glass. * When it is necessary to clamp the LEDs to prevent soldering failure, it is important to minimize the mechanical stress on the LEDs. * Cut the LED leads at room temperature. Cutting the leads at high temperatures may cause failure of the LEDs. (6) Heat Generation * Thermal design of the end product is of paramount importance. Please consider the heat generation of the LED when making the system design. The coefficient of temperature increase per input electric power is affected by the thermal resistance of the circuit board and density of LED placement on the board, as well as other components. It is necessary to avoid intense heat generation and operate within the maximum ratings given in this specification. * The operating current should be decided after considering the ambient maximum temperature of LEDs. (7) Cleaning * It is recommended that isopropyl alcohol be used as a solvent for cleaning the LEDs. When using other solvents, it should be confirmed beforehand whether the solvents will dissolve the resin or not. Freon solvents should not be used to clean the LEDs because of worldwide regulations. * Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic cleaning on the LEDs depends on factors such as ultrasonic power and the assembled condition. Before cleaning, a pre-test should be done to confirm whether any damage to the LEDs will occur. -5- Nichia STSE-CH2058C -6- ! Forward Voltage vs. Forward Current 200 100 50 20 10 5 Ta=25C Forward Current IFP (mA) ! Forward Current vs. Relative Power Output 5 Relative Power Output (a.u.) Ta=25C 4 3 2 1 0 0 20 40 60 80 100 120 Forward Current IFP (mA) ! Duty Ratio vs. Allowable Forward Current Allowable Forward Current IFP (mA) 200 Ta=25C 100 80 50 30 20 10 1 3.0 3.2 3.4 3.6 3.8 4.0 4.2 Forward Voltage VF (V) 1 5 10 20 50 100 Duty Ratio (%) ! Ambient Temperature vs. Forward Voltage 4.0 Forward Voltage VF (V) 3.9 3.8 3.7 3.6 3.5 3.4 3.3 3.2 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (C) IFP=20mA ! Ambient Temperature vs. Relative Power Output 2.0 Relative Power Output (a.u.) IFP=20mA 1.0 ! Ambient Temperature vs. Allowable Forward Current Allowable Forward Current IF (mA) 30 25 20 15 10 5 0 0 20 40 60 80 100 Ambient Temperature Ta (C) -7- 0.5 0.2 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (C) NNichia STSE-CH2058C Model NSHUxxxA NICHIA CORPORATION Title No. TYP.CHARACTERISTICS 040121421401 ! Forward Current vs. Peak Wavelength 379 Peak Wavelength p (nm) Ta=25 377 375 373 371 369 1 5 10 20 50 100 Forward Current IFP (mA) ! Spectrum Relative Emission Intensity (a.u.) 1.2 1.0 0.8 0.6 0.4 0.2 0 300 350 400 450 500 550 600 Wavelength (nm) Ta=25 IF=20mA ! Ambient Temperature vs. Peak Wavelength 379 Peak Wavelength p (nm) ! Directivity (NSHU590A) 1.0 Relative Power Output (a.u.) 0 Ta=25 IF=20mA 10 20 30 40 50 0.5 60 70 80 0 90 60 30 Radiation Angle 0 0.5 90 1.0 -8- IFP=20mA 377 375 373 371 369 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (C) Nichia STSE-CH2058C Model NSHU590A NICHIA CORPORATION Title No. TYP.CHARACTERISTICS 031202200913 Side View 6.2 0.4 Internal circuit A 4.5 0.4 0.5 (2.5) Anode Glass Top View Protection device Cathode K -9- 14.5 1 0.4 1 1 ! NSHU590A has a protection device built in as a protection circuit against static electricity. ITEM GLASS CAP LEAD MATERIALS Hard Glass Ni Plating Iron Alloy Au Plating Iron Alloy Model 4.7 5.4 Nichia STSE-CH2058C NSHU590A Unit mm 5/1 Scale Allow 0.2 NICHIA CORPORATION Title No. OUTLINE DIMENSIONS 020705200151 NICHIA Cardboard UV LED TYPE NSHUxxx LOT QTY xxxxxx-!# pcs Anti electrostatic bag NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN UV LED LE D 1M LE D L ED R A D IA TIO N D O N O T V IE W D IRE CT LY W IT H O PT IC AL IN ST RU M E N T S C LA SS 1M LE D PR O D U CT The quantity is printed on this bag. CAUTION TO ELECTROSTATIC DAMAGE Label NICHIA UV TYPE RANK QTY LED NSHUxxx !# PCS NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN -10- Cardboard Caution Label UV LED LED 1M LED LED RADIATION DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS CLASS 1M LED PRODUCT " Put the label and caution label on the cardboard box. Nichia STSE-CH2058C Cardboard box 360!135!215!4t Model NSHUxxx PACKING 030826314421 NICHIA CORPORATION " One box contains 8 bags at maximum. Title No. Cardboard NICHIA UV LED TYPE NSHUxxx LOT QTY xxxxxx-!# pcs Anti-electrostatic bag NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN UV LED LE D L ED R A D IA TIO N D O N O T V IE W D IRE CT LY W IT H O PT IC AL IN ST RU M E N T S C LA SS 1M LE D PR O D U CT The quantity is printed on this bag. 1M LE D CAUTION TO ELECTROSTATIC DAMAGE Caution Label Cardboard box A LED 1M LED UV LED LED RADIATION DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS CLASS 1M LED PRODUCT -11Cardboard Label " Put the caution label on the cardboard box A. NICHIA UV TYPE RANK QTY LED NSHUxxx !# PCS NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN " Put the label on the cardboard box B. Nichia STSE-CH2058C Cardboard box B 360!135!215!4t " The cardboard box B contains 2 cardboard box A at maximum. Model NSHUxxx PACKING 030826314431 NICHIA CORPORATION Title No. Cardboard Anti-electrostatic bag NICHIA UV LED TYPE NSHUxxx LOT QTY xxxxxx-!# pcs NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN UV LED LE D 1M LE D L ED R A D IA TIO N D O N O T V IE W D IRE CT LY W IT H O PT IC AL IN ST RU M E N T S C LA SS 1M LE D PR O D U CT The quantity is printed on this bag. CAUTION TO ELECTROSTATIC DAMAGE Label NICHIA UV LED NSHUxxx !# PCS TYPE RANK QTY Cardboard Caution Label -12- NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN UV LED LED LED RADIATION DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS CLASS 1M LED PRODUCT Cardboard box 425!135!355!4t 1M LED " Put the label and caution label on the cardboard box. Nichia STSE-CH2058C Model " One box contains 20 bags at maximum. NSHUxxx PACKING 030826314441 NICHIA CORPORATION Title No. NICHIA Cardboard UV LED TYPE NSHUxxx LOT QTY xxxxxx-!# pcs Anti-electrostatic bag NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN UV LED LE D L ED R A D IA TIO N D O N O T V IE W D IRE CT LY W IT H O PT IC AL IN ST RU M E N T S C LA SS 1M LE D PR O D U CT The quantity is printed on this bag. 1M LE D CAUTION TO ELECTROSTATIC DAMAGE Cardboard box A Caution Label UV LED LED 1M LED LED RADIATION DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS CLASS 1M LED PRODUCT -13Cardboard " The cardboard box B contains 4 cardboard box A at maximum. Label " Put the caution label on the cardboard box A. NICHIA UV TYPE RANK QTY LED NSHUxxx !# PCS NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN " Put the label on the cardboard box B. Nichia STSE-CH2058C Cardboard box B 425!135!355!4t Model NSHUxxx PACKING 030826314451 NICHIA CORPORATION Title No. |
Price & Availability of NSHU590A
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |